SoldByOwner › Guides › Can you sell a FSBO home with knob-and-tube wiring?
Can you sell a FSBO home with knob-and-tube wiring?
Short answer: yes — you can sell, and knob-and-tube wiring does not take away the right to sell your own home. What it changes is the buyer pool and the paperwork: insurers and lenders, not the sale itself, are where the friction lives. Knob-and-tube is an early wiring system common in homes built from the 1880s through the 1940s. Existing installations are grandfathered under many local codes when in good condition, but it is not installed new today. The working plan is simple: disclose it in writing, get a licensed electrician's written evaluation before you list, and then fix the hazards found, rewire, or price as-is with the evaluation in the file. Everything below is general information, not legal or electrical advice — a licensed electrician decides the condition of the wiring.
1. What knob-and-tube wiring is
Knob-and-tube was the standard way to wire a house in the era when homes were first electrified, roughly from the 1880s through the 1940s. Instead of the bundled cable used today, separate conductors run through the framing: the wires are supported on ceramic knobs and pass through holes in the joists inside ceramic tubes, which is where the name comes from. Two features matter at sale time. First, there is no grounding conductor — the system predates the grounded outlets modern buyers and inspectors expect. Second, the conductors were designed to dissipate heat in open air, spaced apart inside the wall and attic cavities. Wiring that is original, undisturbed and in good condition is a different file from wiring that has been spliced into, damaged, or buried under blown-in insulation — which is why condition, documented by an electrician, is the whole conversation.
2. Grandfathered in many places — but never installed new
Existing knob-and-tube installations are grandfathered under many local codes when they are in good condition: the code that governs a home today generally does not order an owner to rip out a working system just because a newer method exists. That grandfathered standing is about the right to keep and sell the home, and it ends there. Knob-and-tube is not installed new today, extensions and alterations are commonly required to meet current code, and a local code or a buyer's inspector can still flag specific damaged or altered sections as hazards to correct. Do not argue code with a buyer — put the electrician's written evaluation in the file and let the document carry that conversation.
3. The practical blockers are insurance and financing
Nothing about knob-and-tube wiring prevents you from pricing the home, posting it for sale by owner and talking to buyers. The wall is the financed buyer's closing. Many insurers refuse new policies on homes with active knob-and-tube wiring, or will only quote after a licensed electrician's evaluation — and a buyer who cannot insure the home cannot close a financed purchase, because the lender requires insurance. On the loan side, a buyer's appraiser or home inspector will flag the wiring, and lenders, including government-backed loan programs stated generally, may require hazards to be corrected before the loan proceeds. So the sequence matters: the insurance and lender questions arrive at contract time, and a seller who has already documented the wiring's condition answers them in days instead of losing the buyer.
4. Get a licensed electrician's written evaluation before listing
Before the home goes up, hire a licensed electrician to evaluate the knob-and-tube wiring and put the findings in writing. The evaluation should say which circuits are still active knob-and-tube, what condition the insulation and connections are in, and what hazards, if any, exist. Keep that letter in the pre-listing file with your disclosure form. It does three jobs: it tells you which route below is honest, it gives a buyer's insurer the document many of them ask for before quoting, and it turns a buyer's vague worry about old wiring into a specific, priced conversation. An evaluation is not a guarantee and this page is not electrical advice — the licensed electrician who inspects the wiring decides its condition.
5. The routes, in order — fix the hazards, rewire, or sell as-is
First route: fix the active hazards the electrician finds and get the evaluation or certification letter updated for the file. The hazards that matter most are damaged conductor insulation, improper splices or alterations where later work was tied into the old system, and insulation blown over the wiring — a known hazard because the system was designed to dissipate heat in open air, and covering it traps that heat. Second route: rewire some or all of the circuits before listing, starting with the circuits an insurer or inspector cares about most, so the home is sold with modern wiring where it counts. Third route: sell as-is, priced from recent sold comparables — homes that actually closed, adjusted for condition — with the electrician's evaluation in the file and the wiring disclosed, so the price already carries the work the buyer will do. Cash and investor buyers are the flexible pool on any of these routes, because no insurer or lender is imposing conditions on their purchase.
6. Disclose it, in writing — never hide it
Disclose known knob-and-tube wiring in writing on the state seller disclosure form. A buyer's inspector will find it in the attic or basement anyway; wiring a buyer discovers reads as a surprise and a negotiation, while the same wiring disclosed up front, with the electrician's evaluation and the route you chose, reads as a handled item. If the evaluation found hazards you are not fixing, the disclosure and the as-is pricing say so plainly. Keep the full electrical file — the evaluation letter, any repair or rewiring invoices, and permits where they were pulled — for the buyer, the buyer's insurer and the title company.
7. How the process runs — evaluation first, listing second, closing last
Run it in this order. First, confirm what you have: an electrician can identify knob-and-tube wiring and say how much of it is still active. Second, get the written evaluation before you price or list. Third, choose the route — fix the hazards found, rewire some or all circuits, or sell as-is from recent sold comparables — and price with the evaluation in the file. Fourth, disclose the wiring in writing on the state disclosure form from the first showing, not at contract time. Fifth, expect the buyer's inspector, appraiser and insurer to raise it, and answer with the file you built. For the closing sequence itself, see How does closing work on a FSBO sale?
None of this needs the MLS — SoldByOwner never lists a home on the MLS. SoldByOwner posts your home free, in your own photos and words, in front of buyers and the 6,600 realtors with buyers and 829 directory pros who browse the permissioned feed — and the home is never listed on the MLS, ever. Knob-and-tube wiring changes the electrical file you prepare before your sale; it does not change that posting.
Can you sell a FSBO home with knob-and-tube wiring?
Yes — you can sell a home with knob-and-tube wiring. Knob-and-tube is an early wiring system common in homes built from the 1880s through the 1940s: separate conductors run on ceramic knobs and through ceramic tubes, with no grounding conductor. Existing installations are grandfathered under many local codes when in good condition, but it is not installed new today. Disclose known knob-and-tube in writing on the state disclosure form — never hide it. The practical blockers are insurance and financing, not the right to sell, and a licensed electrician's written evaluation before listing is the document that moves the conversation. This page is general information, not legal or electrical advice — a licensed electrician decides the condition of the wiring.
Why do insurers and lenders make knob-and-tube wiring a problem at sale time?
Because a financed sale needs insurance and a loan, and both sides look hard at old wiring. Many insurers refuse new policies on homes with active knob-and-tube wiring, or require a licensed electrician's evaluation first, and without insurance a financed buyer's loan cannot close. A buyer's appraiser or home inspector will flag the wiring, and lenders — including government-backed loan programs, stated generally — may require hazards to be corrected before the loan proceeds. Cash and investor buyers are the flexible pool, because no insurer or lender is imposing those conditions on their purchase.
What should you do about knob-and-tube wiring before listing a FSBO home?
Get a licensed electrician's written evaluation before listing and keep it in the pre-listing file — the evaluation states what is active, what condition it is in, and what hazards exist. Then choose a route, in this order: fix the active hazards the electrician finds — damaged insulation, improper splices or alterations, and insulation blown over the wiring, which is a known hazard because the system was designed to dissipate heat in open air — and get the electrician's evaluation or certification letter for the file; rewire some or all of the circuits before listing; or sell as-is, priced from recent sold comparables, with the evaluation in the file so buyers and their insurers see a documented condition instead of a surprise.